#Message ID: 12004
#[no translated message!]
#$$$$12004
#\\
#[English]
#Can't seem to write out /etc/resolv.conf.  Net cannot be used.

#Message ID: 12020
#[no translated message!]
#$$$$12020
#\\
#[English]
#Killing previous PPP process %d.

#Message ID: 12019
#[no translated message!]
#$$$$12019
#\\
#[English]
#Killing previous DHCP client %d.

#Message ID: 12000
#[no translated message!]
#$$$$12000
#\\
#[English]
#Unable to start PPP!  This installation method cannot be used.

#Message ID: 12001
#[no translated message!]
#$$$$12001
#\\
#[English]
#Warning:  SLIP is rather poorly supported in this revision
#of the installation due to the lack of a dialing utility.
#If you can use PPP for this instead then you're much better
#off doing so, otherwise SLIP works fairly well for *hardwired*
#links.  Please edit the following slattach command for
#correctness (default here is: VJ compression, Hardware flow-
#control, ignore carrier and 9600 baud data rate).  When you're
#ready, press [ENTER] to execute it.

#Message ID: 12021
#[no translated message!]
#$$$$12021
#\\
#[English]
#slattach command was empty.  Try again!

#Message ID: 12002
#[no translated message!]
#$$$$12002
#\\
#[English]
#slattach returned a bad status!  Please verify that
#the command is correct and try this operation again.

#Message ID: 12005
#[no translated message!]
#$$$$12005
#\\
#[English]
#Unable to configure the %s interface!
#This installation method cannot be used.

#Message ID: 12006
#[no translated message!]
#$$$$12006
#\\
#[English]
#No gateway has been set. You may be unable to access hosts
#not on your local network

#Message ID: 12003
#[no translated message!]
#$$$$12003
#\\
#[English]
#The %s device is not configured.  You will need to do so
#in the Networking configuration menu before proceeding.

#Message ID: 12050
#[no translated message!]
#$$$$12050
#\\
#[English]
#Killing previous PPP process %d.

#Message ID: 12051
#[no translated message!]
#$$$$12051
#\\
#[English]
#Killing previous DHCP client %d.

#Message ID: 12009
#[no translated message!]
#$$$$12009
#\\
#[English]
#Warning: Unable to down the %s interface properly

#Message ID: 12012
#[no translated message!]
#$$$$12012
#\\
#[English]
#Enter the baud rate for your modem - this can be higher than the actual
#maximum data rate since most modems can talk at one speed to the
#computer and at another speed to the remote end.
#If you're not sure what to put here, just select the default.

#Message ID: 12013
#[no translated message!]
#$$$$12013
#\\
#[English]
#Enter the IP address of your service provider or 0 if you
#don't know it and would prefer to negotiate it dynamically.

#Message ID: 12014
#[no translated message!]
#$$$$12014
#\\
#[English]
#Couldn't open %s file!  This isn't going to work

#Message ID: 12032
#[no translated message!]
#$$$$12032
#\\
#[English]
#Does your ISP support PAP or CHAP ppp logins?

#Message ID: 12034
#[no translated message!]
#$$$$12034
#\\
#[English]
#Enter the name you use to login to your provider.

#Message ID: 12036
#[no translated message!]
#$$$$12036
#\\
#[English]
#Enter the password you use to login to your provider.

#Message ID: 12038
#[no translated message!]
#$$$$12038
#\\
#[English]
#Enter the your provider's login phone number.

#Message ID: 12040
#[no translated message!]
#$$$$12040
#\\
#[English]
#Does your telephone line support tone dialing?

#Message ID: 12030
#[no translated message!]
#$$$$12030
#\\
#[English]
#Warning: Failed to fix permissions on /etc/ppp/ppp.conf !

#Message ID: 12015
#[no translated message!]
#$$$$12015
#\\
#[English]
#Warning:  No /dev/tun0 device.  PPP will not work!

#Message ID: 12016
#[no translated message!]
#$$$$12016
#\\
#[English]
#NOTICE: The PPP command is now started on VTY3 (type ALT-F3 to
#interact with it, ALT-F1 to switch back here). If you are using
#a PAP or CHAP login simply enter "dial", otherwise you'll need
#to use the "term" command which starts a terminal emulator
#which you can use to talk to your modem and dial the service
#provider.  Once you're connected, come back to this screen and
#press return.
#DO NOT PRESS [ENTER] HERE UNTIL THE CONNECTION IS FULLY
#ESTABLISHED!

#Message ID: 12052
#[no translated message!]
#$$$$12052
#\\
#[English]
#Couldn't open %s file!  This isn't going to work

