2. Quick Start¶

This section describes the basic steps needed to get Kea up and running. For further details, full customizations, and troubleshooting, see the respective chapters elsewhere in this Kea Administrator Reference Manual (ARM).

2.1. Quick Start Guide Using tarball¶

Install required runtime and build dependencies. See Build Requirements for details.
Download the Kea source tarball from the ISC.org downloads page or the ISC downloads site.
Extract the tarball. For example:
```
$ tar -xvzf kea-2.3.3.tar.gz
```
Go into the source directory and run the configure script:
```
$ cd kea-2.3.3
$ ./configure [your extra parameters]
```
Build it:
```
$ make
```
Install it (by default it will be placed in /usr/local/, so root privileges are likely required for this step):
```
$ make install
```

2.2. Quick Start Guide Using Native Packages¶

ISC provides native Alpine, deb, and RPM packages, which make Kea installation much easier. Unless specific compilation options are desired, it is usually easier to install Kea using native packages.

Go to Kea on cloudsmith.io, choose the Kea version, and enter the repository.
Use Set Me Up and follow instructions to add the repository to the local system.

Note

For example, the Debian setup instructions for Kea 2.3 can be found here: https://cloudsmith.io/~isc/repos/kea-2-3/setup/#formats-deb

You can use the dropdown near the top of the page to get instructions for another OS.

Update system repositories. For example on Debian/Ubuntu:
$ sudo apt update
On CentOS/Fedora:
$ sudo yum update
On Alpine:
# apk update
Kea is split into various packages. The entire list is available on cloudsmith.io or using apt/yum/dnf. For example on Debian/Ubuntu:
$ apt search isc-kea
On CentOS/Fedora:
$ yum search isc-kea
On Alpine:
$ apk search isc-kea
Install the metapackage containing all of the tools, services, and open source hooks:
$ sudo apt install isc-kea
or specific packages:
$ sudo apt install isc-kea-dhcp6
or every single Kea related package, including development headers, debug symbols, and premium hooks (if they are available to you):
$ sudo apt install isc-kea*
or all packages with a specified version number:
$ sudo apt install isc-kea*=1.8.1-isc0000920201106154401

Note

Not all package managers support installing packages with a glob (*), please refer to your package managers manual before attempting to do so.

On CentOS/Fedora systems, replace apt install with yum install
On Alpine systems, replace apt install with apk add

All installed packages should be now available directly; for example:

# kea-dhcp6 -c /path/to/your/kea6/config/file.json

or using systemd:

# systemctl restart kea-dhcp6

or using OpenRC on Alpine:

# service kea-dhcp6 restart

Note

keactrl is not available in packages as similar functionality is provided by the native systemctl scripts.

On CentOS, Fedora, and Alpine, you will need to enable the service at boot time if that is desirable. This is done automatically at package installation time on Debian and Ubuntu systems. For example, with systemd on CentOS/Fedora:
# systemctl enable kea-dhcp6
With OpenRC on Alpine:
# rc-update add kea-dhcp6

2.3. Quick Start Guide for DHCPv4 and DHCPv6 Services¶

Edit the Kea configuration files, which by default are installed in the [kea-install-dir]/etc/kea/ directory. These are: kea-dhcp4.conf, kea-dhcp6.conf, kea-dhcp-ddns.conf and kea-ctrl-agent.conf, keactrl.conf for DHCPv4 server, DHCPv6 server, D2, Control Agent, and the keactrl script, respectively.
To start the DHCPv4 server in the background, run the following command (as root):
```
# keactrl start -s dhcp4
```
Or run the following command to start the DHCPv6 server:
```
# keactrl start -s dhcp6
```
Note that it is also possible to start all servers simultaneously:
```
# keactrl start
```
Verify that the Kea server(s) is/are running:
```
# keactrl status
```
A server status of "inactive" may indicate a configuration error. Please check the log file (by default named [kea-install-dir]/var/log/kea-dhcp4.log, [kea-install-dir]/var/log/kea-dhcp6.log, [kea-install-dir]/var/log/kea-ddns.log, or [kea-install-dir]/var/log/kea-ctrl-agent.log) for the details of any errors.
If the server has started successfully, test that it is responding to DHCP queries and that the client receives a configuration from the server; for example, use the ISC DHCP client.
To stop running the server(s):
```
# keactrl stop
```

For system-specific instructions, please read the system-specific notes, available in the Kea section of ISC's Knowledgebase.

The details of keactrl script usage can be found in Managing Kea with keactrl.

Once Kea services are up and running, consider deploying a dashboard solution to monitor running services. For more details, see Monitoring Kea With Stork.

2.4. Running the Kea Servers Directly¶

The Kea servers can be started directly, without the need to use keactrl or systemctl. To start the DHCPv4 server run the following command:

# kea-dhcp4 -c /path/to/your/kea4/config/file.json

Similarly, to start the DHCPv6 server, run the following command:

# kea-dhcp6 -c /path/to/your/kea6/config/file.json