/* $NetBSD: rtwreg.h,v 1.29 2016/09/15 21:45:37 jdolecek Exp $ */ /*- * Copyright (c) 2004, 2005 David Young. All rights reserved. * * Programmed for NetBSD by David Young. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY David Young ``AS IS'' AND ANY * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A * PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL David * Young BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY * OF SUCH DAMAGE. */ #include /* RTL8180L Host Control and Status Registers */ #define RTW_IDR0 0x00 /* ID Register: MAC addr, 6 bytes. * Auto-loaded from EEPROM. Read by byte, * by word, or by double word, but write * only by double word. */ #define RTW_IDR1 0x04 #define RTW_MAR0 0x08 /* Multicast filter, 64b. */ #define RTW_MAR1 0x0c #define RTW_TSFTRL 0x18 /* Timing Synchronization Function Timer * Register, low word, 32b, read-only. */ #define RTW_TSFTRH 0x1c /* High word, 32b, read-only. */ #define RTW_TLPDA 0x20 /* Transmit Low Priority Descriptors Start * Address, 32b, 256-byte alignment. */ #define RTW_TNPDA 0x24 /* Transmit Normal Priority Descriptors Start * Address, 32b, 256-byte alignment. */ #define RTW_THPDA 0x28 /* Transmit High Priority Descriptors Start * Address, 32b, 256-byte alignment. */ #define RTW_BRSR 0x2c /* Basic Rate Set Register, 16b */ #define RTW_BRSR_BPLCP __BIT(8)/* 1: use short PLCP header for CTS/ACK packet, * 0: use long PLCP header */ #define RTW_BRSR_MBR8180_MASK __BITS(1,0) /* Maximum Basic Service Rate */ #define RTW_BRSR_MBR8180_1MBPS __SHIFTIN(0, RTW_BRSR_MBR8180_MASK) #define RTW_BRSR_MBR8180_2MBPS __SHIFTIN(1, RTW_BRSR_MBR8180_MASK) #define RTW_BRSR_MBR8180_5MBPS __SHIFTIN(2, RTW_BRSR_MBR8180_MASK) #define RTW_BRSR_MBR8180_11MBPS __SHIFTIN(3, RTW_BRSR_MBR8180_MASK) /* 8181 and 8180 docs conflict! */ #define RTW_BRSR_MBR8181_1MBPS __BIT(0) #define RTW_BRSR_MBR8181_2MBPS __BIT(1) #define RTW_BRSR_MBR8181_5MBPS __BIT(2) #define RTW_BRSR_MBR8181_11MBPS __BIT(3) #define RTW_BSSID 0x2e /* BSSID, 6 bytes */ #define RTW_BSSID16 0x2e /* first two bytes */ #define RTW_BSSID32 (0x2e + 4) /* remaining four bytes */ #define RTW_BSSID0 RTW_BSSID16 /* BSSID[0], 8b */ #define RTW_BSSID1 (RTW_BSSID0 + 1) /* BSSID[1], 8b */ #define RTW_BSSID2 (RTW_BSSID1 + 1) /* BSSID[2], 8b */ #define RTW_BSSID3 (RTW_BSSID2 + 1) /* BSSID[3], 8b */ #define RTW_BSSID4 (RTW_BSSID3 + 1) /* BSSID[4], 8b */ #define RTW_BSSID5 (RTW_BSSID4 + 1) /* BSSID[5], 8b */ #define RTW_CR 0x37 /* Command Register, 8b */ #define RTW_CR_RST __BIT(4)/* Reset: host sets to 1 to disable * transmitter & receiver, reinitialize FIFO. * RTL8180L sets to 0 to signal completion. */ #define RTW_CR_RE __BIT(3)/* Receiver Enable: host enables receiver * by writing 1. RTL8180L indicates receiver * is active with 1. After power-up, host * must wait for reset before writing. */ #define RTW_CR_TE __BIT(2)/* Transmitter Enable: host enables transmitter * by writing 1. RTL8180L indicates transmitter * is active with 1. After power-up, host * must wait for reset before writing. */ #define RTW_CR_MULRW __BIT(0)/* PCI Multiple Read/Write enable: 1 enables, * 0 disables. XXX RTL8180, only? */ #define RTW_IMR 0x3c /* Interrupt Mask Register, 16b */ #define RTW_ISR 0x3e /* Interrupt status register, 16b */ #define RTW_INTR_TXFOVW __BIT(15) /* Tx FIFO underflow */ #define RTW_INTR_TIMEOUT __BIT(14) /* Time Out: 1 indicates * RTW_TSFTR[0:31] = RTW_TINT */ /* Beacon Time Out: time for host to prepare beacon: * RTW_TSFTR % (RTW_BCNITV_BCNITV * TU) = * (RTW_BCNITV_BCNITV * TU - RTW_BINTRITV) */ #define RTW_INTR_BCNINT __BIT(13) /* ATIM Time Out: ATIM interval will pass, * RTW_TSFTR % (RTW_BCNITV_BCNITV * TU) = * (RTW_ATIMWND_ATIMWND * TU - RTW_ATIMTRITV) */ #define RTW_INTR_ATIMINT __BIT(12) /* Tx Beacon Descriptor Error: beacon transmission aborted because frame Rx'd */ #define RTW_INTR_TBDER __BIT(11) #define RTW_INTR_TBDOK __BIT(10) /* Tx Beacon Descriptor OK */ #define RTW_INTR_THPDER __BIT(9)/* Tx High Priority Descriptor Error: * reached short/long retry limit */ #define RTW_INTR_THPDOK __BIT(8)/* Tx High Priority Descriptor OK */ #define RTW_INTR_TNPDER __BIT(7)/* Tx Normal Priority Descriptor Error: * reached short/long retry limit */ #define RTW_INTR_TNPDOK __BIT(6)/* Tx Normal Priority Descriptor OK */ #define RTW_INTR_RXFOVW __BIT(5)/* Rx FIFO Overflow: either RDU (see below) * or PCI bus too slow/busy */ #define RTW_INTR_RDU __BIT(4)/* Rx Descriptor Unavailable */ #define RTW_INTR_TLPDER __BIT(3)/* Tx Normal Priority Descriptor Error * reached short/long retry limit */ #define RTW_INTR_TLPDOK __BIT(2)/* Tx Normal Priority Descriptor OK */ #define RTW_INTR_RER __BIT(1)/* Rx Error: CRC32 or ICV error */ #define RTW_INTR_ROK __BIT(0)/* Rx OK */ /* Convenient interrupt conjunctions. */ #define RTW_INTR_RX (RTW_INTR_RER|RTW_INTR_ROK|RTW_INTR_RDU|RTW_INTR_RXFOVW) #define RTW_INTR_TX (RTW_INTR_TLPDER|RTW_INTR_TLPDOK|RTW_INTR_THPDER|\ RTW_INTR_THPDOK|RTW_INTR_TNPDER|RTW_INTR_TNPDOK|\ RTW_INTR_TBDER|RTW_INTR_TBDOK) #define RTW_INTR_BEACON (RTW_INTR_BCNINT|RTW_INTR_TBDER|RTW_INTR_TBDOK) #define RTW_INTR_IOERROR (RTW_INTR_TXFOVW) #define RTW_TCR 0x40 /* Transmit Configuration Register, 32b */ #define RTW_TCR_CWMIN __BIT(31)/* 1: CWmin = 8, 0: CWmin = 32. */ #define RTW_TCR_SWSEQ __BIT(30)/* 1: host assigns 802.11 sequence number, * 0: hardware assigns sequence number */ /* Hardware version ID, read-only */ #define RTW_TCR_HWVERID_MASK __BITS(29, 25) #define RTW_TCR_HWVERID_D __SHIFTIN(26, RTW_TCR_HWVERID_MASK) #define RTW_TCR_HWVERID_F __SHIFTIN(27, RTW_TCR_HWVERID_MASK) #define RTW_TCR_HWVERID_RTL8180 RTW_TCR_HWVERID_F /* Set ACK/CTS Timeout (EIFS). * 1: ACK rate = max(RTW_BRSR_MBR, Rx rate) (XXX not min? typo in datasheet?) * 0: ACK rate = 1Mbps */ #define RTW_TCR_SAT __BIT(24) /* Max DMA Burst Size per Tx DMA Burst */ #define RTW_TCR_MXDMA_MASK __BITS(23,21) #define RTW_TCR_MXDMA_16 __SHIFTIN(0, RTW_TCR_MXDMA_MASK) #define RTW_TCR_MXDMA_32 __SHIFTIN(1, RTW_TCR_MXDMA_MASK) #define RTW_TCR_MXDMA_64 __SHIFTIN(2, RTW_TCR_MXDMA_MASK) #define RTW_TCR_MXDMA_128 __SHIFTIN(3, RTW_TCR_MXDMA_MASK) #define RTW_TCR_MXDMA_256 __SHIFTIN(4, RTW_TCR_MXDMA_MASK) #define RTW_TCR_MXDMA_512 __SHIFTIN(5, RTW_TCR_MXDMA_MASK) #define RTW_TCR_MXDMA_1024 __SHIFTIN(6, RTW_TCR_MXDMA_MASK) #define RTW_TCR_MXDMA_2048 __SHIFTIN(7, RTW_TCR_MXDMA_MASK) /* disable 802.11 random backoff */ #define RTW_TCR_DISCW __BIT(20) /* host lets RTL8180 append ICV to WEP packets */ #define RTW_TCR_ICV __BIT(19) /* Loopback Test: disables TXI/TXQ outputs. */ #define RTW_TCR_LBK_MASK __BITS(18,17) #define RTW_TCR_LBK_NORMAL __SHIFTIN(0, RTW_TCR_LBK_MASK) /* normal ops */ #define RTW_TCR_LBK_MAC __SHIFTIN(1, RTW_TCR_LBK_MASK) /* MAC loopback */ #define RTW_TCR_LBK_BBP __SHIFTIN(2, RTW_TCR_LBK_MASK) /* baseband loop. */ #define RTW_TCR_LBK_CONT __SHIFTIN(3, RTW_TCR_LBK_MASK) /* continuous Tx */ #define RTW_TCR_CRC __BIT(16) /* 0: RTL8180 appends CRC32 * 1: host appends CRC32 * * (I *think* this is right. * The docs have a mysterious * description in the * passive voice.) */ #define RTW_TCR_SRL_MASK __BITS(15,8) /* Short Retry Limit */ #define RTW_TCR_LRL_MASK __BITS(7,0) /* Long Retry Limit */ #define RTW_RCR 0x44 /* Receive Configuration Register, 32b */ /* only do Early Rx on packets longer than 1536 bytes */ #define RTW_RCR_ONLYERLPKT __BIT(31) /* enable carrier sense method 2 */ #define RTW_RCR_ENCS2 __BIT(30) /* enable carrier sense method 1 */ #define RTW_RCR_ENCS1 __BIT(29) #define RTW_RCR_ENMARP __BIT(28) /* enable MAC auto-reset PHY */ /* Check BSSID/ToDS/FromDS: set "Link On" when received BSSID * matches RTW_BSSID and received ToDS/FromDS are appropriate * according to RTW_MSR_NETYPE. */ #define RTW_RCR_CBSSID __BIT(23) /* accept packets w/ PWRMGMT bit set */ #define RTW_RCR_APWRMGT __BIT(22) /* when RTW_MSR_NETYPE == RTW_MSR_NETYPE_INFRA_OK, accept * broadcast/multicast packets whose 3rd address matches RTL8180's MAC. */ #define RTW_RCR_ADD3 __BIT(21) #define RTW_RCR_AMF __BIT(20) /* accept management frames */ #define RTW_RCR_ACF __BIT(19) /* accept control frames */ #define RTW_RCR_ADF __BIT(18) /* accept data frames */ /* Rx FIFO Threshold: RTL8180 begins PCI transfer when this many data * bytes are received */ #define RTW_RCR_RXFTH_MASK __BITS(15,13) #define RTW_RCR_RXFTH_64 __SHIFTIN(2, RTW_RCR_RXFTH_MASK) #define RTW_RCR_RXFTH_128 __SHIFTIN(3, RTW_RCR_RXFTH_MASK) #define RTW_RCR_RXFTH_256 __SHIFTIN(4, RTW_RCR_RXFTH_MASK) #define RTW_RCR_RXFTH_512 __SHIFTIN(5, RTW_RCR_RXFTH_MASK) #define RTW_RCR_RXFTH_1024 __SHIFTIN(6, RTW_RCR_RXFTH_MASK) #define RTW_RCR_RXFTH_WHOLE __SHIFTIN(7, RTW_RCR_RXFTH_MASK) #define RTW_RCR_AICV __BIT(12)/* accept frames w/ ICV errors */ /* Max DMA Burst Size per Rx DMA Burst */ #define RTW_RCR_MXDMA_MASK __BITS(10,8) #define RTW_RCR_MXDMA_16 __SHIFTIN(0, RTW_RCR_MXDMA_MASK) #define RTW_RCR_MXDMA_32 __SHIFTIN(1, RTW_RCR_MXDMA_MASK) #define RTW_RCR_MXDMA_64 __SHIFTIN(2, RTW_RCR_MXDMA_MASK) #define RTW_RCR_MXDMA_128 __SHIFTIN(3, RTW_RCR_MXDMA_MASK) #define RTW_RCR_MXDMA_256 __SHIFTIN(4, RTW_RCR_MXDMA_MASK) #define RTW_RCR_MXDMA_512 __SHIFTIN(5, RTW_RCR_MXDMA_MASK) #define RTW_RCR_MXDMA_1024 __SHIFTIN(6, RTW_RCR_MXDMA_MASK) #define RTW_RCR_MXDMA_UNLIMITED __SHIFTIN(7, RTW_RCR_MXDMA_MASK) /* EEPROM type, read-only. 1: EEPROM is 93c56, 0: 93c46 */ #define RTW_RCR_9356SEL __BIT(6) #define RTW_RCR_ACRC32 __BIT(5)/* accept frames w/ CRC32 errors */ #define RTW_RCR_AB __BIT(3)/* accept broadcast frames */ #define RTW_RCR_AM __BIT(2)/* accept multicast frames */ /* accept physical match frames. XXX means PLCP header ok? */ #define RTW_RCR_APM __BIT(1) #define RTW_RCR_AAP __BIT(0)/* accept frames w/ destination */ /* Additional bits to set in monitor mode. */ #define RTW_RCR_MONITOR ( \ RTW_RCR_AAP | \ RTW_RCR_ACF | \ RTW_RCR_ACRC32 | \ RTW_RCR_AICV | \ 0) /* The packet filter bits. */ #define RTW_RCR_PKTFILTER_MASK (\ RTW_RCR_AAP | \ RTW_RCR_AB | \ RTW_RCR_ACF | \ RTW_RCR_ACRC32 | \ RTW_RCR_ADD3 | \ RTW_RCR_ADF | \ RTW_RCR_AICV | \ RTW_RCR_AM | \ RTW_RCR_AMF | \ RTW_RCR_APM | \ RTW_RCR_APWRMGT | \ 0) /* Receive power-management frames and mgmt/ctrl/data frames. */ #define RTW_RCR_PKTFILTER_DEFAULT ( \ RTW_RCR_ACF | \ RTW_RCR_ADF | \ RTW_RCR_AMF | \ RTW_RCR_APM | \ RTW_RCR_APWRMGT | \ 0) #define RTW_TINT 0x48 /* Timer Interrupt Register, 32b */ #define RTW_TBDA 0x4c /* Transmit Beacon Descriptor Start Address, * 32b, 256-byte alignment */ #define RTW_9346CR 0x50 /* 93c46/93c56 Command Register, 8b */ #define RTW_9346CR_EEM_MASK __BITS(7,6) /* Operating Mode */ #define RTW_9346CR_EEM_NORMAL __SHIFTIN(0, RTW_9346CR_EEM_MASK) /* Load the EEPROM. Reset registers to defaults. * Takes ~2ms. RTL8180 indicates completion with RTW_9346CR_EEM_NORMAL. * XXX RTL8180 only? */ #define RTW_9346CR_EEM_AUTOLOAD __SHIFTIN(1, RTW_9346CR_EEM_MASK) /* Disable network & bus-master operations and enable * _EECS, _EESK, _EEDI, _EEDO. * XXX RTL8180 only? */ #define RTW_9346CR_EEM_PROGRAM __SHIFTIN(2, RTW_9346CR_EEM_MASK) /* Enable RTW_CONFIG[0123] registers. */ #define RTW_9346CR_EEM_CONFIG __SHIFTIN(3, RTW_9346CR_EEM_MASK) /* EEPROM pin status/control in _EEM_CONFIG, _EEM_AUTOLOAD modes. * XXX RTL8180 only? */ #define RTW_9346CR_EECS __BIT(3) #define RTW_9346CR_EESK __BIT(2) #define RTW_9346CR_EEDI __BIT(1) #define RTW_9346CR_EEDO __BIT(0) /* read-only */ #define RTW_CONFIG0 0x51 /* Configuration Register 0, 8b */ #define RTW_CONFIG0_WEP40 __BIT(7)/* implements 40-bit WEP, * XXX RTL8180 only? */ #define RTW_CONFIG0_WEP104 __BIT(6)/* implements 104-bit WEP, * from EEPROM, read-only * XXX RTL8180 only? */ #define RTW_CONFIG0_LEDGPOEN __BIT(4)/* 1: RTW_PSR_LEDGPO[01] control * LED[01] pins. * 0: LED behavior defined by * RTW_CONFIG1_LEDS10_MASK * XXX RTL8180 only? */ /* auxiliary power is present, read-only */ #define RTW_CONFIG0_AUXPWR __BIT(3) /* Geographic Location, read-only */ #define RTW_CONFIG0_GL_MASK __BITS(1,0) /* _RTW_CONFIG0_GL_* is what the datasheet says, but RTW_CONFIG0_GL_* * work. */ #define _RTW_CONFIG0_GL_USA __SHIFTIN(3, RTW_CONFIG0_GL_MASK) #define RTW_CONFIG0_GL_EUROPE __SHIFTIN(2, RTW_CONFIG0_GL_MASK) #define RTW_CONFIG0_GL_JAPAN __SHIFTIN(1, RTW_CONFIG0_GL_MASK) #define RTW_CONFIG0_GL_USA __SHIFTIN(0, RTW_CONFIG0_GL_MASK) /* RTL8181 datasheet says RTW_CONFIG0_GL_JAPAN = 0. */ #define RTW_CONFIG1 0x52 /* Configuration Register 1, 8b */ /* LED configuration. From EEPROM. Read/write. * * Setting LED0 LED1 * ------- ---- ---- * RTW_CONFIG1_LEDS_ACT_INFRA Activity Infrastructure * RTW_CONFIG1_LEDS_ACT_LINK Activity Link * RTW_CONFIG1_LEDS_TX_RX Tx Rx * RTW_CONFIG1_LEDS_LINKACT_INFRA Link/Activity Infrastructure */ #define RTW_CONFIG1_LEDS_MASK __BITS(7,6) #define RTW_CONFIG1_LEDS_ACT_INFRA __SHIFTIN(0, RTW_CONFIG1_LEDS_MASK) #define RTW_CONFIG1_LEDS_ACT_LINK __SHIFTIN(1, RTW_CONFIG1_LEDS_MASK) #define RTW_CONFIG1_LEDS_TX_RX __SHIFTIN(2, RTW_CONFIG1_LEDS_MASK) #define RTW_CONFIG1_LEDS_LINKACT_INFRA __SHIFTIN(3, RTW_CONFIG1_LEDS_MASK) /* LWAKE Output Signal. Only applicable to Cardbus. Pulse width is 150ms. * * RTW_CONFIG1_LWACT * 0 1 * RTW_CONFIG4_LWPTN 0 active high active low * 1 positive pulse negative pulse */ #define RTW_CONFIG1_LWACT __BIT(4) #define RTW_CONFIG1_MEMMAP __BIT(3)/* using PCI memory space, read-only */ #define RTW_CONFIG1_IOMAP __BIT(2)/* using PCI I/O space, read-only */ #define RTW_CONFIG1_VPD __BIT(1)/* if set, VPD from offsets * 0x40-0x7f in EEPROM are at * registers 0x60-0x67 of PCI * Configuration Space (XXX huh?) */ #define RTW_CONFIG1_PMEN __BIT(0)/* Power Management Enable: TBD */ #define RTW_CONFIG2 0x53 /* Configuration Register 2, 8b */ #define RTW_CONFIG2_LCK __BIT(7)/* clocks are locked, read-only: * Tx frequency & symbol clocks * are derived from the same OSC */ #define RTW_CONFIG2_ANT __BIT(6) /* diversity enabled, read-only */ #define RTW_CONFIG2_DPS __BIT(3) /* Descriptor Polling State: enable * test mode. */ #define RTW_CONFIG2_PAPESIGN __BIT(2) /* TBD, from EEPROM */ #define RTW_CONFIG2_PAPETIME_MASK __BITS(1,0) /* TBD, from EEPROM */ #define RTW_ANAPARM 0x54 /* Analog parameter, 32b */ #define RTW_ANAPARM_RFPOW0_MASK __BITS(30,28) /* undocumented bits * which appear to * control the power * state of the RF * components */ #define RTW_ANAPARM_RFPOW_MASK \ (RTW_ANAPARM_RFPOW0_MASK|RTW_ANAPARM_RFPOW1_MASK) #define RTW_ANAPARM_TXDACOFF __BIT(27) /* 1: disable Tx DAC, * 0: enable */ #define RTW_ANAPARM_RFPOW1_MASK __BITS(26,20) /* undocumented bits * which appear to * control the power * state of the RF * components */ /* * Maxim On/Sleep/Off control */ #define RTW_ANAPARM_RFPOW_MAXIM_ON __SHIFTIN(0x8, RTW_ANAPARM_RFPOW1_MASK) /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ #define RTW_ANAPARM_RFPOW_MAXIM_SLEEP __SHIFTIN(0x378, RTW_ANAPARM_RFPOW1_MASK) /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ #define RTW_ANAPARM_RFPOW_MAXIM_OFF __SHIFTIN(0x379, RTW_ANAPARM_RFPOW1_MASK) /* * RFMD On/Sleep/Off control */ #define RTW_ANAPARM_RFPOW_RFMD_ON __SHIFTIN(0x408, RTW_ANAPARM_RFPOW1_MASK) /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ #define RTW_ANAPARM_RFPOW_RFMD_SLEEP __SHIFTIN(0x378, RTW_ANAPARM_RFPOW1_MASK) /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ #define RTW_ANAPARM_RFPOW_RFMD_OFF __SHIFTIN(0x379, RTW_ANAPARM_RFPOW1_MASK) /* * Philips On/Sleep/Off control */ #define RTW_ANAPARM_RFPOW_ANA_PHILIPS_ON \ __SHIFTIN(0x328, RTW_ANAPARM_RFPOW1_MASK) #define RTW_ANAPARM_RFPOW_DIG_PHILIPS_ON \ __SHIFTIN(0x008, RTW_ANAPARM_RFPOW1_MASK) /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ #define RTW_ANAPARM_RFPOW_PHILIPS_SLEEP\ __SHIFTIN(0x378, RTW_ANAPARM_RFPOW1_MASK) /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ #define RTW_ANAPARM_RFPOW_PHILIPS_OFF\ __SHIFTIN(0x379, RTW_ANAPARM_RFPOW1_MASK) #define RTW_ANAPARM_RFPOW_PHILIPS_ON __SHIFTIN(0x328, RTW_ANAPARM_RFPOW1_MASK) #define RTW_ANAPARM_CARDSP_MASK __BITS(19,0) /* undocumented * card-specific * bits from the * EEPROM. */ #define RTW_MSR 0x58 /* Media Status Register, 8b */ /* Network Type and Link Status */ #define RTW_MSR_NETYPE_MASK __BITS(3,2) /* AP, XXX RTL8181 only? */ #define RTW_MSR_NETYPE_AP_OK __SHIFTIN(3, RTW_MSR_NETYPE_MASK) /* infrastructure link ok */ #define RTW_MSR_NETYPE_INFRA_OK __SHIFTIN(2, RTW_MSR_NETYPE_MASK) /* ad-hoc link ok */ #define RTW_MSR_NETYPE_ADHOC_OK __SHIFTIN(1, RTW_MSR_NETYPE_MASK) /* no link */ #define RTW_MSR_NETYPE_NOLINK __SHIFTIN(0, RTW_MSR_NETYPE_MASK) #define RTW_CONFIG3 0x59 /* Configuration Register 3, 8b */ #define RTW_CONFIG3_GNTSEL __BIT(7) /* Grant Select, read-only */ #define RTW_CONFIG3_PARMEN __BIT(6) /* Set RTW_CONFIG3_PARMEN and * RTW_9346CR_EEM_CONFIG to * allow RTW_ANAPARM writes. */ #define RTW_CONFIG3_MAGIC __BIT(5)/* Valid when RTW_CONFIG1_PMEN is * set. If set, RTL8180 wakes up * OS when Magic Packet is Rx'd. */ #define RTW_CONFIG3_CARDBEN __BIT(3)/* Cardbus-related registers * and functions are enabled, * read-only. XXX RTL8180 only. */ #define RTW_CONFIG3_CLKRUNEN __BIT(2)/* CLKRUN enabled, read-only. * XXX RTL8180 only. */ #define RTW_CONFIG3_FUNCREGEN __BIT(1)/* Function Registers Enabled, * read-only. XXX RTL8180 only. */ #define RTW_CONFIG3_FBTBEN __BIT(0)/* Fast back-to-back enabled, * read-only. */ #define RTW_CONFIG4 0x5A /* Configuration Register 4, 8b */ #define RTW_CONFIG4_VCOPDN __BIT(7)/* VCO Power Down * 0: normal operation * (power-on default) * 1: power-down VCO, RF front-end, * and most RTL8180 components. */ #define RTW_CONFIG4_PWROFF __BIT(6)/* Power Off * 0: normal operation * (power-on default) * 1: power-down RF front-end, * and most RTL8180 components, * but leave VCO on. * * XXX RFMD front-end only? */ #define RTW_CONFIG4_PWRMGT __BIT(5)/* Power Management * 0: normal operation * (power-on default) * 1: set Tx packet's PWRMGMT bit. */ #define RTW_CONFIG4_LWPME __BIT(4)/* LANWAKE vs. PMEB: Cardbus-only * 0: LWAKE & PMEB asserted * simultaneously * 1: LWAKE asserted only if * both PMEB is asserted and * ISOLATEB is low. * XXX RTL8180 only. */ #define RTW_CONFIG4_LWPTN __BIT(2)/* see RTW_CONFIG1_LWACT * XXX RTL8180 only. */ /* Radio Front-End Programming Method */ #define RTW_CONFIG4_RFTYPE_MASK __BITS(1,0) #define RTW_CONFIG4_RFTYPE_INTERSIL __SHIFTIN(1, RTW_CONFIG4_RFTYPE_MASK) #define RTW_CONFIG4_RFTYPE_RFMD __SHIFTIN(2, RTW_CONFIG4_RFTYPE_MASK) #define RTW_CONFIG4_RFTYPE_PHILIPS __SHIFTIN(3, RTW_CONFIG4_RFTYPE_MASK) #define RTW_TESTR 0x5B /* TEST mode register, 8b */ #define RTW_PSR 0x5e /* Page Select Register, 8b */ #define RTW_PSR_GPO __BIT(7)/* Control/status of pin 52. */ #define RTW_PSR_GPI __BIT(6)/* Status of pin 64. */ #define RTW_PSR_LEDGPO1 __BIT(5)/* Status/control of LED1 pin if * RTW_CONFIG0_LEDGPOEN is set. */ #define RTW_PSR_LEDGPO0 __BIT(4)/* Status/control of LED0 pin if * RTW_CONFIG0_LEDGPOEN is set. */ #define RTW_PSR_UWF __BIT(1)/* Enable Unicast Wakeup Frame */ #define RTW_PSR_PSEN __BIT(0)/* 1: page 1, 0: page 0 */ #define RTW_SCR 0x5f /* Security Configuration Register, 8b */ #define RTW_SCR_KM_MASK __BITS(5,4) /* Key Mode */ #define RTW_SCR_KM_WEP104 __SHIFTIN(1, RTW_SCR_KM_MASK) #define RTW_SCR_KM_WEP40 __SHIFTIN(0, RTW_SCR_KM_MASK) #define RTW_SCR_TXSECON __BIT(1)/* Enable Tx WEP. Invalid if * neither RTW_CONFIG0_WEP40 nor * RTW_CONFIG0_WEP104 is set. */ #define RTW_SCR_RXSECON __BIT(0)/* Enable Rx WEP. Invalid if * neither RTW_CONFIG0_WEP40 nor * RTW_CONFIG0_WEP104 is set. */ #define RTW_BCNITV 0x70 /* Beacon Interval Register, 16b */ #define RTW_BCNITV_BCNITV_MASK __BITS(9,0) /* TU between TBTT, written * by host. */ #define RTW_ATIMWND 0x72 /* ATIM Window Register, 16b */ #define RTW_ATIMWND_ATIMWND __BITS(9,0) /* ATIM Window length in TU, * written by host. */ #define RTW_BINTRITV 0x74 /* Beacon Interrupt Interval Register, 16b */ #define RTW_BINTRITV_BINTRITV __BITS(9,0) /* RTL8180 wakes host with * RTW_INTR_BCNINT at BINTRITV * microseconds before TBTT */ #define RTW_ATIMTRITV 0x76 /* ATIM Interrupt Interval Register, 16b */ #define RTW_ATIMTRITV_ATIMTRITV __BITS(9,0) /* RTL8180 wakes host with * RTW_INTR_ATIMINT at ATIMTRITV * microseconds before end of * ATIM Window */ #define RTW_PHYDELAY 0x78 /* PHY Delay Register, 8b */ #define RTW_PHYDELAY_REVC_MAGIC __BIT(3) /* Rev. C magic from reference * driver */ #define RTW_PHYDELAY_PHYDELAY __BITS(2,0) /* microsecond Tx delay between * MAC and RF front-end */ #define RTW_CRCOUNT 0x79 /* Carrier Sense Counter, 8b */ #define RTW_CRCOUNT_MAGIC 0x4c #define RTW_CRC16ERR 0x7a /* CRC16 error count, 16b, XXX RTL8181 only? */ #define RTW_BB 0x7c /* Baseband interface, 32b */ /* used for writing RTL8180's integrated baseband processor */ #define RTW_BB_RD_MASK __BITS(23,16) /* data to read */ #define RTW_BB_WR_MASK __BITS(15,8) /* data to write */ #define RTW_BB_WREN __BIT(7) /* write enable */ #define RTW_BB_ADDR_MASK __BITS(6,0) /* address */ #define RTW_PHYADDR 0x7c /* Address register for PHY interface, 8b */ #define RTW_PHYDATAW 0x7d /* Write data to PHY, 8b, write-only */ #define RTW_PHYDATAR 0x7e /* Read data from PHY, 8b (?), read-only */ #define RTW_PHYCFG 0x80 /* PHY Configuration Register, 32b */ #define RTW_PHYCFG_MAC_POLL __BIT(31) /* if !RTW_PHYCFG_HST, * host sets. MAC clears * after banging bits. */ #define RTW_PHYCFG_HST __BIT(30) /* 1: host bangs bits * 0: MAC bangs bits */ #define RTW_PHYCFG_MAC_RFTYPE_MASK __BITS(29,28) #define RTW_PHYCFG_MAC_RFTYPE_INTERSIL __SHIFTIN(0, RTW_PHYCFG_MAC_RFTYPE_MASK) #define RTW_PHYCFG_MAC_RFTYPE_RFMD __SHIFTIN(1, RTW_PHYCFG_MAC_RFTYPE_MASK) #define RTW_PHYCFG_MAC_RFTYPE_GCT RTW_PHYCFG_MAC_RFTYPE_RFMD #define RTW_PHYCFG_MAC_RFTYPE_PHILIPS __SHIFTIN(3, RTW_PHYCFG_MAC_RFTYPE_MASK) #define RTW_PHYCFG_MAC_PHILIPS_ADDR_MASK __BITS(27,24) #define RTW_PHYCFG_MAC_PHILIPS_DATA_MASK __BITS(23,0) #define RTW_PHYCFG_MAC_MAXIM_LODATA_MASK __BITS(27,24) #define RTW_PHYCFG_MAC_MAXIM_ADDR_MASK __BITS(11,8) #define RTW_PHYCFG_MAC_MAXIM_HIDATA_MASK __BITS(7,0) #define RTW_PHYCFG_HST_EN __BIT(2) #define RTW_PHYCFG_HST_CLK __BIT(1) #define RTW_PHYCFG_HST_DATA __BIT(0) #define RTW_MAXIM_HIDATA_MASK __BITS(11,4) #define RTW_MAXIM_LODATA_MASK __BITS(3,0) /** ** 0x84 - 0xD3, page 1, selected when RTW_PSR[PSEN] == 1. **/ #define RTW_WAKEUP0L 0x84 /* Power Management Wakeup Frame */ #define RTW_WAKEUP0H 0x88 /* 32b */ #define RTW_WAKEUP1L 0x8c #define RTW_WAKEUP1H 0x90 #define RTW_WAKEUP2LL 0x94 #define RTW_WAKEUP2LH 0x98 #define RTW_WAKEUP2HL 0x9c #define RTW_WAKEUP2HH 0xa0 #define RTW_WAKEUP3LL 0xa4 #define RTW_WAKEUP3LH 0xa8 #define RTW_WAKEUP3HL 0xac #define RTW_WAKEUP3HH 0xb0 #define RTW_WAKEUP4LL 0xb4 #define RTW_WAKEUP4LH 0xb8 #define RTW_WAKEUP4HL 0xbc #define RTW_WAKEUP4HH 0xc0 #define RTW_CRC0 0xc4 /* CRC of wakeup frame 0, 16b */ #define RTW_CRC1 0xc6 /* CRC of wakeup frame 1, 16b */ #define RTW_CRC2 0xc8 /* CRC of wakeup frame 2, 16b */ #define RTW_CRC3 0xca /* CRC of wakeup frame 3, 16b */ #define RTW_CRC4 0xcc /* CRC of wakeup frame 4, 16b */ /** ** 0x84 - 0xD3, page 0, selected when RTW_PSR[PSEN] == 0. **/ /* Default Key Registers, each 128b * * If RTW_SCR_KM_WEP104, 104 lsb are the key. * If RTW_SCR_KM_WEP40, 40 lsb are the key. */ #define RTW_DK0 0x90 /* Default Key 0 Register, 128b */ #define RTW_DK1 0xa0 /* Default Key 1 Register, 128b */ #define RTW_DK2 0xb0 /* Default Key 2 Register, 128b */ #define RTW_DK3 0xc0 /* Default Key 3 Register, 128b */ #define RTW_CONFIG5 0xd8 /* Configuration Register 5, 8b */ #define RTW_CONFIG5_TXFIFOOK __BIT(7)/* Tx FIFO self-test pass, read-only */ #define RTW_CONFIG5_RXFIFOOK __BIT(6)/* Rx FIFO self-test pass, read-only */ #define RTW_CONFIG5_CALON __BIT(5)/* 1: start calibration cycle * and raise AGCRESET pin. * 0: lower AGCRESET pin */ #define RTW_CONFIG5_EACPI __BIT(2)/* Enable ACPI Wake up, default 0 */ #define RTW_CONFIG5_LANWAKE __BIT(1)/* Enable LAN Wake signal, * from EEPROM */ #define RTW_CONFIG5_PMESTS __BIT(0)/* 1: both software & PCI Reset * reset PME_Status * 0: only software resets PME_Status * * From EEPROM. */ #define RTW_TPPOLL 0xd9 /* Transmit Priority Polling Register, 8b, * write-only. */ #define RTW_TPPOLL_BQ __BIT(7)/* RTL8180 clears to notify host of a beacon * Tx. Host writes have no effect. */ #define RTW_TPPOLL_HPQ __BIT(6)/* Host writes 1 to notify RTL8180 of * high-priority Tx packets, RTL8180 clears * to after high-priority Tx is complete. */ #define RTW_TPPOLL_NPQ __BIT(5)/* If RTW_CONFIG2_DPS is set, * host writes 1 to notify RTL8180 of * normal-priority Tx packets, RTL8180 clears * after normal-priority Tx is complete. * * If RTW_CONFIG2_DPS is clear, host writes * have no effect. RTL8180 clears after * normal-priority Tx is complete. */ #define RTW_TPPOLL_LPQ __BIT(4)/* Host writes 1 to notify RTL8180 of * low-priority Tx packets, RTL8180 clears * after low-priority Tx is complete. */ #define RTW_TPPOLL_SBQ __BIT(3)/* Host writes 1 to tell RTL8180 to * stop beacon DMA. This bit is invalid * when RTW_CONFIG2_DPS is set. */ #define RTW_TPPOLL_SHPQ __BIT(2)/* Host writes 1 to tell RTL8180 to * stop high-priority DMA. */ #define RTW_TPPOLL_SNPQ __BIT(1)/* Host writes 1 to tell RTL8180 to * stop normal-priority DMA. This bit is invalid * when RTW_CONFIG2_DPS is set. */ #define RTW_TPPOLL_SLPQ __BIT(0)/* Host writes 1 to tell RTL8180 to * stop low-priority DMA. */ /* Start all queues. */ #define RTW_TPPOLL_ALL (RTW_TPPOLL_BQ | RTW_TPPOLL_HPQ | \ RTW_TPPOLL_NPQ | RTW_TPPOLL_LPQ) /* Check all queues' activity. */ #define RTW_TPPOLL_ACTIVE RTW_TPPOLL_ALL /* Stop all queues. */ #define RTW_TPPOLL_SALL (RTW_TPPOLL_SBQ | RTW_TPPOLL_SHPQ | \ RTW_TPPOLL_SNPQ | RTW_TPPOLL_SLPQ) #define RTW_CWR 0xdc /* Contention Window Register, 16b, read-only */ /* Contention Window: indicates number of contention windows before Tx */ #define RTW_CWR_CW __BITS(9,0) /* Retry Count Register, 16b, read-only */ #define RTW_RETRYCTR 0xde /* Retry Count: indicates number of retries after Tx */ #define RTW_RETRYCTR_RETRYCT __BITS(7,0) #define RTW_RDSAR 0xe4 /* Receive descriptor Start Address Register, * 32b, 256-byte alignment. */ /* Function Event Register, 32b, Cardbus only. Only valid when * both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN are set. */ #define RTW_FER 0xf0 #define RTW_FER_INTR __BIT(15) /* set when RTW_FFER_INTR is set */ #define RTW_FER_GWAKE __BIT(4) /* General Wakeup */ /* Function Event Mask Register, 32b, Cardbus only. Only valid when * both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN are set. */ #define RTW_FEMR 0xf4 #define RTW_FEMR_INTR __BIT(15) /* set when RTW_FFER_INTR is set */ #define RTW_FEMR_WKUP __BIT(14) /* Wakeup Mask */ #define RTW_FEMR_GWAKE __BIT(4) /* General Wakeup */ /* Function Present State Register, 32b, read-only, Cardbus only. * Only valid when both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN * are set. */ #define RTW_FPSR 0xf8 #define RTW_FPSR_INTR __BIT(15) /* TBD */ #define RTW_FPSR_GWAKE __BIT(4) /* General Wakeup: TBD */ /* Function Force Event Register, 32b, write-only, Cardbus only. * Only valid when both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN * are set. */ #define RTW_FFER 0xfc #define RTW_FFER_INTR __BIT(15) /* TBD */ #define RTW_FFER_GWAKE __BIT(4) /* General Wakeup: TBD */ /* Serial EEPROM offsets */ #define RTW_SR_ID 0x00 /* 16b */ #define RTW_SR_VID 0x02 /* 16b */ #define RTW_SR_DID 0x04 /* 16b */ #define RTW_SR_SVID 0x06 /* 16b */ #define RTW_SR_SMID 0x08 /* 16b */ #define RTW_SR_MNGNT 0x0a #define RTW_SR_MXLAT 0x0b #define RTW_SR_RFCHIPID 0x0c #define RTW_SR_CONFIG3 0x0d #define RTW_SR_MAC 0x0e /* 6 bytes */ #define RTW_SR_CONFIG0 0x14 #define RTW_SR_CONFIG1 0x15 #define RTW_SR_PMC 0x16 /* Power Management Capabilities, 16b */ #define RTW_SR_CONFIG2 0x18 #define RTW_SR_CONFIG4 0x19 #define RTW_SR_ANAPARM 0x1a /* Analog Parameters, 32b */ #define RTW_SR_TESTR 0x1e #define RTW_SR_CONFIG5 0x1f #define RTW_SR_TXPOWER1 0x20 #define RTW_SR_TXPOWER2 0x21 #define RTW_SR_TXPOWER3 0x22 #define RTW_SR_TXPOWER4 0x23 #define RTW_SR_TXPOWER5 0x24 #define RTW_SR_TXPOWER6 0x25 #define RTW_SR_TXPOWER7 0x26 #define RTW_SR_TXPOWER8 0x27 #define RTW_SR_TXPOWER9 0x28 #define RTW_SR_TXPOWER10 0x29 #define RTW_SR_TXPOWER11 0x2a #define RTW_SR_TXPOWER12 0x2b #define RTW_SR_TXPOWER13 0x2c #define RTW_SR_TXPOWER14 0x2d #define RTW_SR_CHANNELPLAN 0x2e /* bitmap of channels to scan */ #define RTW_SR_ENERGYDETTHR 0x2f /* energy-detect threshold */ #define RTW_SR_ENERGYDETTHR_DEFAULT 0x0c /* use this if old SROM */ #define RTW_SR_CISPOINTER 0x30 /* 16b */ #define RTW_SR_RFPARM 0x32 /* RF-specific parameter */ #define RTW_SR_RFPARM_DIGPHY __BIT(0) /* 1: digital PHY */ #define RTW_SR_RFPARM_DFLANTB __BIT(1) /* 1: antenna B is default */ #define RTW_SR_RFPARM_CS_MASK __BITS(2,3) /* carrier-sense type */ #define RTW_SR_VERSION 0x3c /* EEPROM content version, 16b */ #define RTW_SR_CRC 0x3e /* EEPROM content CRC, 16b */ #define RTW_SR_VPD 0x40 /* Vital Product Data, 64 bytes */ #define RTW_SR_CIS 0x80 /* CIS Data, 93c56 only, 128 bytes*/ /* * RTL8180 Transmit/Receive Descriptors */ /* the first descriptor in each ring must be on a 256-byte boundary */ #define RTW_DESC_ALIGNMENT 256 /* Tx descriptor */ struct rtw_txdesc { volatile uint32_t td_ctl0; volatile uint32_t td_ctl1; volatile uint32_t td_buf; volatile uint32_t td_len; volatile uint32_t td_next; volatile uint32_t td_rsvd[3]; } __packed __aligned(4); #define td_stat td_ctl0 #define RTW_TXCTL0_OWN __BIT(31) /* 1: ready to Tx */ #define RTW_TXCTL0_RSVD0 __BIT(30) /* reserved */ #define RTW_TXCTL0_FS __BIT(29) /* first segment */ #define RTW_TXCTL0_LS __BIT(28) /* last segment */ #define RTW_TXCTL0_RATE_MASK __BITS(27,24) /* Tx rate */ #define RTW_TXCTL0_RATE_1MBPS __SHIFTIN(0, RTW_TXCTL0_RATE_MASK) #define RTW_TXCTL0_RATE_2MBPS __SHIFTIN(1, RTW_TXCTL0_RATE_MASK) #define RTW_TXCTL0_RATE_5MBPS __SHIFTIN(2, RTW_TXCTL0_RATE_MASK) #define RTW_TXCTL0_RATE_11MBPS __SHIFTIN(3, RTW_TXCTL0_RATE_MASK) #define RTW_TXCTL0_RTSEN __BIT(23) /* RTS Enable */ #define RTW_TXCTL0_RTSRATE_MASK __BITS(22,19) /* Tx rate */ #define RTW_TXCTL0_RTSRATE_1MBPS __SHIFTIN(0, RTW_TXCTL0_RTSRATE_MASK) #define RTW_TXCTL0_RTSRATE_2MBPS __SHIFTIN(1, RTW_TXCTL0_RTSRATE_MASK) #define RTW_TXCTL0_RTSRATE_5MBPS __SHIFTIN(2, RTW_TXCTL0_RTSRATE_MASK) #define RTW_TXCTL0_RTSRATE_11MBPS __SHIFTIN(3, RTW_TXCTL0_RTSRATE_MASK) #define RTW_TXCTL0_BEACON __BIT(18) /* packet is a beacon */ #define RTW_TXCTL0_MOREFRAG __BIT(17) /* another fragment * follows */ /* add short PLCP preamble and header */ #define RTW_TXCTL0_SPLCP __BIT(16) #define RTW_TXCTL0_KEYID_MASK __BITS(15,14) /* default key id */ #define RTW_TXCTL0_RSVD1_MASK __BITS(13,12) /* reserved */ #define RTW_TXCTL0_TPKTSIZE_MASK __BITS(11,0) /* Tx packet size * in bytes */ #define RTW_TXSTAT_OWN RTW_TXCTL0_OWN #define RTW_TXSTAT_RSVD0 RTW_TXCTL0_RSVD0 #define RTW_TXSTAT_FS RTW_TXCTL0_FS #define RTW_TXSTAT_LS RTW_TXCTL0_LS #define RTW_TXSTAT_RSVD1_MASK __BITS(27,16) #define RTW_TXSTAT_TOK __BIT(15) #define RTW_TXSTAT_RTSRETRY_MASK __BITS(14,8) /* RTS retry count */ #define RTW_TXSTAT_DRC_MASK __BITS(7,0) /* Data retry count */ #define RTW_TXCTL1_LENGEXT __BIT(31) /* supplements _LENGTH * in packets sent 5.5Mb/s or * faster */ #define RTW_TXCTL1_LENGTH_MASK __BITS(30,16) /* PLCP length (microseconds) */ #define RTW_TXCTL1_RTSDUR_MASK __BITS(15,0) /* RTS Duration * (microseconds) */ #define RTW_TXLEN_LENGTH_MASK __BITS(11,0) /* Tx buffer length in bytes */ /* Rx descriptor */ struct rtw_rxdesc { volatile uint32_t rd_ctl; volatile uint32_t rd_rsvd0; volatile uint32_t rd_buf; volatile uint32_t rd_rsvd1; } __packed __aligned(4); #define rd_stat rd_ctl #define rd_rssi rd_rsvd0 #define rd_tsftl rd_buf /* valid only when RTW_RXSTAT_LS is set */ #define rd_tsfth rd_rsvd1 /* valid only when RTW_RXSTAT_LS is set */ #define RTW_RXCTL_OWN __BIT(31) /* 1: owned by NIC */ #define RTW_RXCTL_EOR __BIT(30) /* end of ring */ #define RTW_RXCTL_FS __BIT(29) /* first segment */ #define RTW_RXCTL_LS __BIT(28) /* last segment */ #define RTW_RXCTL_RSVD0_MASK __BITS(29,12) /* reserved */ #define RTW_RXCTL_LENGTH_MASK __BITS(11,0) /* Rx buffer length */ #define RTW_RXSTAT_OWN RTW_RXCTL_OWN #define RTW_RXSTAT_EOR RTW_RXCTL_EOR #define RTW_RXSTAT_FS RTW_RXCTL_FS /* first segment */ #define RTW_RXSTAT_LS RTW_RXCTL_LS /* last segment */ #define RTW_RXSTAT_DMAFAIL __BIT(27) /* DMA failure on this pkt */ #define RTW_RXSTAT_BOVF __BIT(26) /* buffer overflow XXX means * FIFO exhausted? */ #define RTW_RXSTAT_SPLCP __BIT(25) /* Rx'd with short preamble * and PLCP header */ #define RTW_RXSTAT_RSVD1 __BIT(24) /* reserved */ #define RTW_RXSTAT_RATE_MASK __BITS(23,20) /* Rx rate */ #define RTW_RXSTAT_RATE_1MBPS __SHIFTIN(0, RTW_RXSTAT_RATE_MASK) #define RTW_RXSTAT_RATE_2MBPS __SHIFTIN(1, RTW_RXSTAT_RATE_MASK) #define RTW_RXSTAT_RATE_5MBPS __SHIFTIN(2, RTW_RXSTAT_RATE_MASK) #define RTW_RXSTAT_RATE_11MBPS __SHIFTIN(3, RTW_RXSTAT_RATE_MASK) #define RTW_RXSTAT_MIC __BIT(19) /* XXX from reference driver */ #define RTW_RXSTAT_MAR __BIT(18) /* is multicast */ #define RTW_RXSTAT_PAR __BIT(17) /* matches RTL8180's MAC */ #define RTW_RXSTAT_BAR __BIT(16) /* is broadcast */ #define RTW_RXSTAT_RES __BIT(15) /* error summary. valid when * RTW_RXSTAT_LS set. indicates * that either RTW_RXSTAT_CRC32 * or RTW_RXSTAT_ICV is set. */ #define RTW_RXSTAT_PWRMGT __BIT(14) /* 802.11 PWRMGMT bit is set */ #define RTW_RXSTAT_CRC16 __BIT(14) /* XXX CRC16 error, from * reference driver */ #define RTW_RXSTAT_CRC32 __BIT(13) /* CRC32 error */ #define RTW_RXSTAT_ICV __BIT(12) /* ICV error */ #define RTW_RXSTAT_LENGTH_MASK __BITS(11,0) /* frame length, including * CRC32 */ /* Convenient status conjunction. */ #define RTW_RXSTAT_ONESEG (RTW_RXSTAT_FS|RTW_RXSTAT_LS) /* Convenient status disjunctions. */ #define RTW_RXSTAT_IOERROR (RTW_RXSTAT_DMAFAIL|RTW_RXSTAT_BOVF) #define RTW_RXSTAT_DEBUG (RTW_RXSTAT_SPLCP|RTW_RXSTAT_MAR|\ RTW_RXSTAT_PAR|RTW_RXSTAT_BAR|\ RTW_RXSTAT_PWRMGT|RTW_RXSTAT_CRC32|\ RTW_RXSTAT_ICV) #define RTW_RXRSSI_VLAN __BITS(31,16) /* XXX from reference driver */ /* for Philips RF front-ends */ #define RTW_RXRSSI_RSSI __BITS(15,8) /* RF energy at the PHY */ /* for RF front-ends by Intersil, Maxim, RFMD */ #define RTW_RXRSSI_IMR_RSSI __BITS(15,9) /* RF energy at the PHY */ #define RTW_RXRSSI_IMR_LNA __BIT(8) /* 1: LNA activated */ #define RTW_RXRSSI_SQ __BITS(7,0) /* Barker code-lock quality */ #define RTW_READ8(regs, ofs) \ bus_space_read_1((regs)->r_bt, (regs)->r_bh, (ofs)) #define RTW_READ16(regs, ofs) \ bus_space_read_2((regs)->r_bt, (regs)->r_bh, (ofs)) #define RTW_READ(regs, ofs) \ bus_space_read_4((regs)->r_bt, (regs)->r_bh, (ofs)) #define RTW_WRITE8(regs, ofs, val) \ bus_space_write_1((regs)->r_bt, (regs)->r_bh, (ofs), (val)) #define RTW_WRITE16(regs, ofs, val) \ bus_space_write_2((regs)->r_bt, (regs)->r_bh, (ofs), (val)) #define RTW_WRITE(regs, ofs, val) \ bus_space_write_4((regs)->r_bt, (regs)->r_bh, (ofs), (val)) #define RTW_ISSET(regs, reg, mask) \ (RTW_READ((regs), (reg)) & (mask)) #define RTW_CLR(regs, reg, mask) \ RTW_WRITE((regs), (reg), RTW_READ((regs), (reg)) & ~(mask)) /* * Registers for RTL8180L's built-in baseband modem. */ #define RTW_BBP_SYS1 0x00 #define RTW_BBP_TXAGC 0x03 /* guess: transmit auto gain control */ #define RTW_BBP_LNADET 0x04 /* guess: low-noise amplifier activation * threshold */ #define RTW_BBP_IFAGCINI 0x05 /* guess: intermediate frequency (IF) * auto-gain control (AGC) initial value */ #define RTW_BBP_IFAGCLIMIT 0x06 /* guess: IF AGC maximum value */ #define RTW_BBP_IFAGCDET 0x07 /* guess: activation threshold for * IF AGC loop */ #define RTW_BBP_ANTATTEN 0x10 /* guess: antenna & attenuation */ #define RTW_BBP_ANTATTEN_GCT_MAGIC 0xa3 #define RTW_BBP_ANTATTEN_PHILIPS_MAGIC 0x91 #define RTW_BBP_ANTATTEN_INTERSIL_MAGIC 0x92 #define RTW_BBP_ANTATTEN_RFMD_MAGIC 0x93 #define RTW_BBP_ANTATTEN_MAXIM_MAGIC 0xb3 #define RTW_BBP_ANTATTEN_DFLANTB 0x40 #define RTW_BBP_ANTATTEN_CHAN14 0x0c #define RTW_BBP_TRL 0x11 /* guess: transmit/receive * switch latency */ #define RTW_BBP_SYS2 0x12 #define RTW_BBP_SYS2_ANTDIV 0x80 /* enable antenna diversity */ #define RTW_BBP_SYS2_RATE_MASK __BITS(5,4) /* loopback rate? * 0: 1Mbps * 1: 2Mbps * 2: 5.5Mbps * 3: 11Mbps */ #define RTW_BBP_SYS3 0x13 /* carrier-sense threshold */ #define RTW_BBP_SYS3_CSTHRESH_MASK __BITS(0,3) #define RTW_BBP_CHESTLIM 0x19 /* guess: channel energy-detect * threshold */ #define RTW_BBP_CHSQLIM 0x1a /* guess: channel signal-quality * threshold */